|
Use of the Appendix
Section I of appendix C sets out the mandatory criteria for personal fall arrest systems used by all employees using powered platforms, as
required by paragraph (j)(1) of this standard. Section II sets out nonmandatory test procedures which may be used to determine compliance with
applicable requirements contained in section I of this appendix. Section III provides nonmandatory guidelines which are intended to assist employers
in complying with these provisions.
I. "Personal fall arrest systems" - (a) "Scope and application." This section establishes the application of and performance criteria for
personal fall arrest systems which are required for use by all employees using powered platforms under paragraph 1910.66(j).
(b) "Definitions."
"Anchorage" means a secure point of attachment for lifelines, lanyards or deceleration devices, and which is independent of the means of
supporting or suspending the employee.
"Body belt" means a strap with means both for securing it about the waist and for attaching it to a lanyard. lifeline, or deceleration
device.
"Body harness" means a design of straps which may be secured about the employee in a manner to distribute the fall arrest forces over at
least the thighs, pelvis. waist, chest and shoulders with means for attaching it,to other components of a personal fall arrest system.
"Buckle" means any device for holding the body belt or body harness closed around the employee's body.
"Competent person" means a person who is capable of identifying hazardous or dangerous conditions in the personal fall arrest system or
any component thereof, as well as in their application and use with related equipment.
"Connector" means a device which is used to couple (connect) parts of the system together. It may be an independent component of the
system (such as a carabiner), or an integral component of part of the system (such as a buckle or dee-ring sewn into a body belt or body harness, or a
snap-hook spliced or sewn to a lanyard or self-retracting lanyard).
"Deceleration device" means any mechanism, such as a rope grab, ripstitch lanyard, specially woven lanyard, tearing or deforming lanyard,
or automatic self retracting-lifeline/lanyard, which serves to dissipate a substantial amount of energy during a fall arrest, or otherwise limits the
energy imposed on an employee during fall arrest.
"Deceleration distance" means the additional vertical distance a falling employee travels, excluding lifeline elongation and free fall
distance, before stopping, from the point at which the deceleration device begins to operate. It is measured as the distance between the location of
an employee's body belt or body harness attachment point at the moment of activation (at the onset of fall arrest forces) of the deceleration device
during a fall, and the location of that attachment point after the employee comes to a full stop.
"Equivalent" means alternative designs materials or methods which the employer can demonstrate will provide an equal or greater degree of
safety for employees than the methods, materials or designs specified in the standard.
"Free fall" means the act of falling before the personal fall arrest system begins to apply force to arrest the fall.
"Free fall distance" means the vertical displacement of the fall arrest attachment point on the employee's body belt or body harness
between onset of the fall and just before the system begins to apply force to arrest the fall. This distance excludes deceleration distance, lifeline
and lanyard elongation but include any deceleration device slide distance or self-retracting lifeline/lanyard extension before they operate and fall
arrest forces occur.
"Lanyard" means a flexible line of rope, wire rope, or strap which is used to secure the body belt or body harness to a deceleration
device, lifeline, or anchorage.
"Lifeline" means a component consisting of a flexible line for connection to an anchorage at one end to hang vertically (vertical
lifeline), or for connection to anchorages at both ends to stretch horizontally (horizontal lifeline), and which serves as a means for connecting
other components of a personal fall arrest system to the anchorage.
"Personal fall arrest system" means a system used to arrest an employee in a fall from a working level. It consists of an anchorage,
connectors, a body belt or body harness and may include a lanyard, deceleration device, lifeline, or suitable combinations of these.
"Qualified person" means one with a recognized degree or professional certificate and extensive knowledge and experience in the subject
field who is capable of design, analysis, evaluation and specifications in the subject work, project, or product.
"Rope grab" means a deceleration device which travels on a lifeline and automatically frictionally engages the lifeline and locks so as to
arrest the fall of an employee. A rope grab usually employs the principle of inertial locking, cam/lever locking, or both.
"Self-retracting lifeline/lanyard" means a deceleration device which contains a drum wound line which may be slowly extracted from, or
retracted onto, the drum under slight tension during normal employee movement, and which, after onset of a fall, automatically locks the drum and
arrests the fall.
"Snap-hook" means a connector comprised of a hookshaped member with a normally closed keeper, or similar arrangement, which may be opened
to permit the hook to receive an object and, when released, automatically closes to retain the object. Snap-hooks are generally one of two
types:
1. The locking type with a self-closing, self-locking keeper which remains closed and locked until unlocked and pressed open for
connection or disconnection, or
2. The non-locking type with a self-closing keeper which remains closed until pressed open for connection or disconnection.
"Tie-off' means the act of an employee, wearing personal fall protection equipment, connecting directly or indirectly to an anchorage. It
also means the condition of an employee being connected to an anchorage.
(c) Design for system components. (1) Connectors shall be drop forged, pressed or formed steel, or made of equivalent materials.
(2) Connectors shall have a corrosion-resistant finish, and all surfaces and edges shall be smooth to prevent damage to interfacing parts
of the system.
(3) Lanyards and vertical lifelines which tie-off one employee shall have a minimum breaking strength of 5,000 pounds (22.2 kN).
(4) Self-retracting lifelines and lanyards which automatically limit free fall distance to two feet (0.61 m) or less shall have components
capable of sustaining a minimum static tensile load of 3,000 pounds (13.3 kN) applied to the device with the lifeline or lanyard in the fully extended
position.
(5) Self-retracting lifelines and lanyards which do not limit free fall distance to two feet (0.61 m) or less, ripstitch lanyards, and
tearing and deforming lanyards shall be capable of sustaining a minimum tensile load of 5,000 pounds (22.2 kN) applied to the device with the lifeline
or lanyard in the fully extended position.
(6) Dee-rings and snap-hooks shall be capable of sustaining a minimum tensile load of 5,000 pounds (22.2 kN).
(7) Dee-rings and snap-hooks shall be 100 percent proof-tested to a minimum tensile load of 3,600 pounds (16 kN) without cracking,
breaking, or taking permanent deformation.
(8) Snap-hooks shall be sized to be compatible with the member to which they are connected so as to prevent unintentional disengagement of
the snap-hook by depression of the snap-hook keeper by the connected member, or shall be a locking type snap-hook designed and used to prevent
disengagement of the snap-hook by the contact of the snaphook keeper by the connected member.
(9) Horizontal lifelines, where used, shall be designed, and installed as part of a complete personal fall arrest system, which maintains
a safety factor of at least two, under the supervision of a qualified person.
(10) Anchorages to which personal fall arrest equipment is attached shall be capable of supporting at least 5,000 pounds (22.2 kN) per
employee attached, or shall be designed, installed, and used as part of a complete personal fall arrest system which maintains a safety factor of at
least two, under the supervision of a qualified person.
(11) Ropes and straps (webbing) used in lanyards, lifelines, and strength components of body belts and body harnesses, shall be made from
synthetic fibers or wire rope.
(d) "System performance criteria." (1) Personal fall arrest systems shall, when stopping a fall:
(i) Limit maximum arresting force on an employee to 900 pounds (4 kN) when used with a body belt;
(ii) Limit maximum arresting force on an employee to 1,800 pounds (8 kN) when used with a body harness;
(iii) Bring an employee to a complete stop and limit maximum deceleration distance an employee travels to 3.5 feet (1.07 m); and
(iv) Shall have sufficient strength to withstand twice the potential impact energy of an employee free falling a distance of six feet (1.8
m), or the free fall distance permitted by the system, whichever is less.
(2)(i) When used by employees having a combined person and tool weight of less than 310 pounds (140 kg), personal fall arrest systems
which meet the criteria and protocols contained in paragraphs (b), (c) and (d) in section II of this appendix shall be considered as complying with
the provisions of paragraphs (d)(1)(i) through (d)(1)(iv) above.
(ii) When used by employees having a combined tool and body weight of 310 pounds (140 kg) or more, personal fall arrest systems which meet
the criteria and protocols contained in paragraphs (b), (c) and (d) in section II may be considered as complying with the provisions of paragraphs
(d)(1)(i) through (d)(1)(iv) provided that the criteria and protocols are modified appropriately to provide proper protection for such heavier
weights.
(e) "Care and use." (1) Snap-hooks, unless of a locking type designed and used to prevent disengagement from the following connections,
shall not be engaged:
(i) Directly to webbing, rope or wire rope;
(ii) To each other;
(iii) To a dee-ring to which another snap-hook or other connector is attached;
(iv) To a horizontal lifeline; or
(v) To any object which is incompatibly shaped or dimensioned in relation to the snap-hook such that the connected object could depress
the snap-hook keeper a sufficient amount to release itself.
(2) Devices used to connect to a horizontal lifeline which may become a vertical lifeline shall be capable of locking in either direction
on the lifeline.
(3) Personal fall arrest systems shall be rigged such that an employee can neither free fall more than six feet (1.8 m), nor contact any
lower level.
(4) The attachment point of the body belt shall be located in the center of the wearer's back. The attachment point of the body harness
shall be located in the center of the wearer's back near shoulder level, or above the wearer's head.
(5) When vertical lifelines are used, each employee shall be provided with a separate lifeline.
(6) Personal fall arrest systems or components shall be used only for employee fall protection.
(7) Personal fall arrest systems or components subjected to impact loading shall be immediately removed from service and shall not be used
again for employee protection unless inspected and determined by a competent person to be undamaged and suitable for reuse.
(8) The employer shall provide for prompt rescue of employees in the event of a fall or shall assure the self-rescue capability of
employees.
(9) Before using a personal fall arrest system and after any component or system is changed, employees shall be trained in accordance with
the requirements of paragraph 1910.66(i)(1), in the safe use of the system.
(f) "Inspections." Personal fall arrest systems shall be inspected prior to each use for mildew, wear, damage and other deterioration, and
defective components shall be removed from service if their strength or function may be adversely affected.
II. "Test methods for personal fall arrest systems (non-mandatory)" - (a) "General." Paragraphs (b), (c), (d) and (e), of this section II
set forth test procedures which may be used to determine compliance with the requirements in paragraph (d)(1)(i) through (d)(1)(iv) of section I of
this appendix.
(b) "General conditions for all tests in section II." (1) Lifelines, lanyards and deceleration devices should be attached to an anchorage
and connected to the body-belt or body harness in the same manner as they would be when used to protect employees.
(2) The anchorage should be rigid, and should not have a deflection greater than .04 inches (1 mm) when a force of 2,250 pounds (10 kN) is
applied.
(3) The frequency response of the load measuring instrumentation should be 120 Hz.
(4) The test weight used in the strength and force tests should be a rigid, metal, cylindrical or torso-shaped object with a girth of 38
inches plus or minus four inches (96 cm plus or minus 10 cm).
(5) The lanyard or lifeline used to create the free fall distance should be supplied with the system, or in its absence, the least elastic
lanyard or lifeline available to be used with the system.
(6) The test weight for each test should be hoisted to the required level and should be quickly released without having any appreciable
motion imparted to it.
(7) The system's performance should be evaluated taking into account the range of environmental conditions for which it is designed to be
used.
(8) Following the test, the system need not be capable of further operation.
(c) "Strength test." (1) During the testing of all systems a test weight of 300 pounds plus or minus five pounds (135 kg plus or minus 2.5
kg) should be used. (See paragraph (b)(4), above.)
(2) The test consists of dropping the test weight once. A new unused system should be used for each test.
(3) For lanyard systems, the lanyard length should be six feet plus or minus two inches (1.83 m plus or minus 5 cm) as measured from the
fixed anchorage to the attachment on the body belt or body harness.
(4) For rope-grab-type deceleration systems, the length of the lifeline above the centerline of the grabbing mechanism to the lifeline's
anchorage point should not exceed two feet (0.61 m).
(5) For lanyard systems, for systems with deceleration devices which do not automatically limit free fall distance to two feet (0.61 m) or
less, and for systems with deceleration devices which have a connection distance in excess of one foot (0.3 m) (measured between the centerline of the
lifeline and the attachment point to the body belt or harness), the test weight should be rigged to free fall a distance of 7.5 feet (2.3 m) from a
point that is 1.5 feet (46 cm) above the anchorage point, to its hanging location (six feet below the anchorage). The test weight should fall without
interference, obstruction, or hitting the floor or ground during the test. In some cases a non-elastic wire lanyard of sufficient length may need to
be added to the system (for test purposes) to create the necessary free fall distance.
(6) For deceleration device systems with integral lifelines or lanyards which automatically limit free fall distance to two feet (0.61 m)
or less, the test weight should be rigged to free fall a distance of four feet (1.22 m).
(7) Any weight which detaches from the belt or harness should constitute failure for the strength test.
(d) "Force test" - (1) "General." The test consists of dropping the respective test weight specified in (d)(2)(i) or (d)(3)(i) once. A
new, unused system should be used for each test.
(2) "For lanyard systems." (i) A test weight of 220 pounds plus or minus three pounds (100 kg plus or minus 1.6 kg) should be used. (See
paragraph (b)(4), above.)
(ii) Lanyard length should be six feet plus or minus two inches (1.83 m plus or minus 5 cm) as measured from the fixed anchorage to the
attachment on the body belt or body harness.
(iii) The test weight should fall free from the anchorage level to its hanging location (a total of six feet (1.83 m) free fall distance)
without interference, obstruction, or hitting the floor or ground during the test.
(3) "For all other systems." (i) A test weight of 220 pounds plus or minus three pounds (100 kg plus or minus 1.6 kg) should be used. (See
paragraph (b)(4), above.)
(ii) The free fall distance to be used in the test should be the maximum fall distance physically permitted by the system during normal
use conditions, up to a maximum free fall distance for the test weight of six feet (1.83 m), except as follows:
(A) For deceleration systems which have a connection link or lanyard, the test weight should free fall a distance equal to the connection
distance (measured between the centerline of the lifeline and the attachment point to the body belt or harness).
(B) For deceleration device systems with integral lifelines or lanyards which automatically limit free fall distance to two feet (0.61 m)
or less, the test weight should free fall a distance equal to that permitted by the system in normal use. (For example, to test a system with a
self-retracting lifeline or lanyard, the test weight should be supported and the system allowed to retract the lifeline or lanyard as it would in
normal use. The test weight would then be released and the force and deceleration distance measured).
(4) A system fails the force test if the recorded maximum arresting force exceeds 1,260 pounds (15.6 kN) when using a body belt, and/or
exceeds 2,520 pounds (11.2 kN) when using a body harness.
(5) The maximum elongation and deceleration distance should be recorded during the force test.
(e) "Deceleration device tests" - (1) "General." The device should be evaluated or tested under the environmental conditions. (such as
rain, ice, grease, dirt, type of lifeline, etc.), for which the device is designed.
(2) "Rope-grab-type deceleration devices." (i) Devices should be moved on a lifeline 1,000 times over the same length of line a distance
of not less than one foot (30.5 cm), and the mechanism should lock each time.
(ii) Unless the device is permanently marked to indicate the type(s) of lifeline which must be used, several types (different diameters
and different materials), of lifelines should be used to test the device.
(3) "Other self-activating-type deceleration devices." The locking mechanisms of other self-activating-type deceleration devices designed
for more than one arrest should lock each of 1,000 times as they would in normal service.
III. "Additional non-mandatory guidelines for personal full arrest systems." The following information constitutes additional guidelines
for use in complying with requirements for a personal fall arrest system.
(a) "Selection and use considerations." The kind of personal fall arrest system selected should match the particular work situation, and
any possible free fall distance should be kept to a minimum. Consideration should be given to the particular work environment. For example, the
presence of acids, dirt, moisture, oil, grease, etc., and their effect on the system, should be evaluated. Hot or cold environments may also have an
adverse affect on the system. Wire rope should not be used where an electrical hazard is anticipated. As required by the standard, the employer must
plan to have means available to promptly rescue an employee should a fall occur, since the suspended employee may not be able to reach a work level
independently.
Where lanyards. connectors. and lifelines are subject to damage by work operations such as welding, chemical cleaning, and sandblasting,
the component should be protected, or other securing systems should be used. The employer should fully evaluate the work conditions and environment
(including seasonal weather changes) before selecting the appropriate personal fall protection system. Once in use, the system's effectiveness should
be monitored. In some cases, a program for cleaning and maintenance of the system may be necessary.
(b) "Testing considerations." Before purchasing or putting into use a personal fall arrest system, an employer should obtain from the
supplier information about the system based on its performance during testing so that the employer can know if the system meets this standard. Testing
should be done using recognized test methods. Section II of this appendix C contains test methods recognized for evaluating the performance of fall
arrest systems. Not all systems may need to be individually tested; the performance of some systems may be based on data and calculations derived from
testing of similar systems, provided that enough information is available to demonstrate similarity of function and design.
(c) "Comment compatibility considerations." Ideally, a personal fall arrest system is designed, tested, and supplied as a complete system.
However, it is common practice for lanyards, connectors, lifelines, deceleration devices, body belts and body harnesses to be interchanged since some
components wear out before others. The employer and employee should realize that not all components are interchangeable. For instance, a lanyard
should not be connected between a body belt (or harness) and a deceleration device of the self-retracting type since this can result in additional
free fall for which the system was not designed. Any substitution or change to a personal fall arrest system should be fully evaluated or tested by a
competent person to determine that it meets the standard, before the modified system is put in use.
(d) "Employee training considerations." Thorough employee training in the selection and use of personal fall arrest systems is imperative.
As stated in the standard, before the equipment is used, employees must be trained in the safe use of the system. This should include the following:
Application limits; proper anchoring and tie-off techniques; estimation of free fall distance, including determination of deceleration distance, and
total fall distance to prevent striking a lower level; methods of use; and inspection and storage of the system. Careless or improper use of the
equipment can result in serious injury or death. Employers and employees should become familiar with the material in this appendix, as well as
manufacturer's recommendations, before a system is used. Of uppermost importance is the reduction in strength caused by certain tie-offs (such as
using knots, tying around sharp edges, etc.) and maximum permitted free fall distance. Also, to be stressed are the importance of inspections prior to
use, the limitations of the equipment, and unique conditions at the worksite which may be important in determining the type of system to
use.
(e) "Instruction considerations." Employers should obtain comprehensive instructions from the supplier as to the system's proper use and
application, including, where applicable:
(1) The force measured during the sample force test;
(2) The maximum elongation measured for lanyards during the force test;
(3) The deceleration distance measured for deceleration devices during the force test;
(4) Caution statements on critical use limitations;
(5) Application limits;
(6) Proper hook-op, anchoring and tie-off techniques, including the proper dee-ring or other attachment point to use on the body belt and
harness for fall arrest;
(7) Proper climbing techniques;
(8) Methods of inspection, use, cleaning, and storage; and
(9) Specific lifelines which may be used. This information should be provided to employees during training.
(f) "Inspection considerations." As stated in the standard (section I, Paragraph (f)), personal fall arrest systems must be regularly
inspected. Any component with any significant defect, such as cuts, tears, abrasions, mold, or undue stretching; alterations or additions which might
affect its efficiency; damage due to deterioration; contact with fire, acids, or other corrosives; distorted hooks or faulty hook springs; tongues
unfitted to the shoulder of buckles; loose or damaged mountings; non-functioning parts; or wearing or internal deterioration in the ropes must be
withdrawn from service immediately, and should be tagged or marked as unusable, or destroyed.
(g) "Rescue considerations." As required by the standard (section I Paragraph (e)(8)), when personal fall arrest systems are used, the
employer must assure that employees can be promptly rescued or can rescue themselves should a fall occur. The availability of rescue personnel,
ladders or other rescue equipment should be evaluated. In some situations, equipment which allows employees to rescue themselves after the fall has
been arrested may be desirable, such as devices which have descent capability.
(h) "Tie-off considerations." (1) One of the most important aspects of personal fall protection systems is fully planning the system
"before" it is put into use. Probably the most overlooked component is planning for suitable anchorage points. Such planning should ideally be done
before the structure or building is constructed so that anchorage points can be incorporated during construction for use later for window cleaning or
other building maintenance. If properly planned, these anchorage points may be used "during" construction, as well as afterwards.
(2) Employers and employees should at all times be aware that the strength of a personal fall arrest system is based on its being attached
to an anchoring system which does not significantly reduce the strength of the system (such as a properly dimensioned eye-bolt/snap-hook anchorage).
Therefore, if a means of attachment is used that will reduce the strength of the system, that component should be replaced by a stronger one, but one
that will also maintain the appropriate maximum arrest force characteristics.
(3) Tie-off using a knot in a rope lanyard or lifeline (at any location) can reduce the lifeline or lanyard strength by 50 percent or
more. Therefore, a stronger lanyard or lifeline should be used to compensate for the weakening effect of the knot, or the lanyard length should be
reduced (or the tie-off location raised) to minimize free fall distance, or the lanyard or lifeline should be replaced by one which has an
appropriately incorporated connector to eliminate the need for a knot.
(4) Tie-off of a rope lanyard or lifeline around an "H" or "I" beam or similar support can reduce its strength as much as 70 percent due
to the cutting action of the beam edges. Therefore, use should be made of a webbing lanyard or wire core lifeline around the beam; or the lanyard or
lifeline should be protected from the edge: or free fall distance should be greatly minimized.
(5) Tie-off where the line passes over or around rough or sharp surfaces reduces strength drastically. Such a tie-off should be avoided or
an alternative tie-off rigging should be used. Such alternatives may include use of a snap-hook/dee ring connection, wire rope tie-off, an effective
padding of the surfaces, or an abrasion-resistance strap around or over the problem surface.
(6) Horizontal lifelines may, depending on their geometry and angle of sag, be subjected to greater loads than the impact load imposed by
an attached component. When the angle of horizontal lifeline sag is less than 30 degrees, the impact force imparted to the lifeline by an attached
lanyard is greatly amplified. For example, with a sag angle of 15 degrees, the force amplification is about 2:1 and at 5 degrees sag, it is about 6:1.
Depending on the angle of sag, and the line's elasticity, the strength of the horizontal lifeline and the anchorages to which it is attached should be
increased a number of times over that of the lanyard. Extreme care should be taken in considering a horizontal lifeline for multiple tie-offs. The
reason for this is that in multiple tie-offs to a horizontal lifeline, if one employee falls, the movement of the falling employee and the horizontal
lifeline during arrest of the fall may cause other employees to also fall. Horizontal lifeline and anchorage strength should be increased for each
additional employee to be tied-off. For these and other reasons, the design of systems using horizontal lifelines must only be done by qualified
persons. Testing of installed lifelines and anchors prior to use is recommended.
(7) The strength of an eye-bolt is rated along the axis of the bolt and its strength is greatly reduced if the force is applied at an
angle to this axis (in the direction of shear). Also, care should be exercised in selecting the proper diameter of the eye to avoid accidental
disengagement of snap-hooks not designed to be compatible for the connection.
(8) Due to the significant reduction in the strength of the lifeline/lanyard (in some cases, as much as a 70 percent reduction), the
sliding hitch knot should not be used for lifeline/lanyard connections except in emergency situations where no other available system is practical.
The "one-and-one" sliding hitch knot should never be used because it is unreliable in stopping a fall. The "two-and-two," or "three-and-three" knot
(preferable), may be used in emergency situations; however, care should be taken to limit free fall distance to a minimum because of reduced
lifeline/lanyard strength.
(i) "Vertical lifeline considerations." As required by the standard, each employee must have a separate lifeline when the lifeline is
vertical. The reason for this is that in multiple tie-offs to a single lifeline, if one employee falls, the movement of the lifeline during the arrest
of the fall may pull other employees' lanyards, causing them to fall as well.
(j) "Snap-hook considerations." Although not required by this standard for all connections, locking snap-hooks designed for connection to
suitable objects (of sufficient strength) are highly recommended in lieu of the non-locking type. Locking snap-hooks incorporate a positive locking
mechanism in addition to the spring loaded keeper, which will not allow the keeper to open under moderate pressure without someone first releasing the
mechanism. Such a feature, properly designed, effectively prevents roll-out from occurring.
As required by the standard (section I, paragraph (e)(1)) the following connections must be avoided (unless properly designed locking
snap-hooks are used) because they are conditions which can result in roll-out when a nonlocking snap-hook is used:
- Direct connection of a snap-hook to horizontal lifeline.
- Two (or more) snap-hooks connected to one dee-ring.
- Two snap-hooks connected to each other.
- A snap-hook connected back on its integral lanyard.
- A snap-hook connected to a webbing loop or webbing lanyard.
- Improper dimensions of the dee-ring, rebar, or other connection
point in relation to the snap-hook dimensions which would allow the
snap-hook keeper to be depressed by a turning motion of the
snap-hook.
(k) "Free fall considerations." The employer and employee should at all times be aware that a system's maximum arresting force is
evaluated under normal use conditions established by the manufacturer, and in no case using a free fall distance in excess of six feet (1.8 m). A few
extra feet of free fall can significantly increase the arresting force on the employee, possibly to the point of causing injury. Because of this, the
free fall distance should be kept at a minimum, and, as required by the standard, in no case greater than six feet (1-8 m). To help assure this, the
tie-off attachment point to the lifeline or anchor should be located at or above the connection point of the fall arrest equipment to belt or harness.
(Since otherwise additional free fall distance is added to the length of the connecting means (i.e. lanyard)). Attaching to the working surface will
often result in a free fall greater than six feet (1.8 m). For instance, if a six foot (1.8 m) lanyard is used, the total free fall distance will be
the distance from the working level to the body belt (or harness) attachment point plus the six feet (1.8 m) of lanyard length. Another important
consideration is that the arresting force which the fall system must withstand also goes up with greater distances of free fall, possibly exceeding
the strength of the system.
(l) "Elongation and deceleration distance considerations." Other factors involved in a proper tie-off are elongation and deceleration
distance. During the arresting of a fall, a lanyard will experience a length of stretching or elongation, whereas activation of a deceleration device
will result in a certain stopping distance. These distances should be available with the lanyard or device's instructions and must be added to the
free fall distance to arrive at the total fall distance before an employee is fully stopped. The additional stopping distance may be very significant
if the lanyard or deceleration device is attached near or at the end of a long lifeline, which may itself add considerable distance due to its own
elongation. As required by the standard, sufficient distance to allow for all of these factors must also be maintained between the employee and
obstructions below, to prevent an injury due to impact before the system fully arrests the fall. In addition, a minimum of 12 feet (3.7 m) of lifeline
should be allowed below the securing point of a rope grab type deceleration device, and the end terminated to prevent the device from sliding off the
lifeline. Alternatively, the lifeline should extend to the ground or the next working level below. These measures are suggested to prevent the worker
from inadvertently moving past the end of the lifeline and having the rope grab become disengaged from the lifeline.
(m) "Obstruction considerations." The location of the tie-off should also consider the hazard of obstructions in the potential fall path
of the employee. Tie-offs which minimize the possibilities of exaggerated swinging should be considered. In addition, when a body belt is used, the
employee's body will go through a horizontal position to a jack-knifed position during the arrest of all falls. Thus, obstructions which might
interfere with this motion should be avoided or a severe injury could occur.
(n) "Other considerations." Because of the design of some personal fall arrest systems, additional considerations may be required for
proper tie-off. For example, heavy deceleration devices of the self-retracting type should be secured overhead in order to avoid the weight of the
device having to be supported by the employee. Also, if self-retracting equipment is connected to a horizontal lifeline, the sag in the lifeline
should be minimized to prevent the device from sliding down the lifeline to a position which creates a swing hazard during fall arrest. In all cases,
manufacturer's instructions should be followed.
| 
